dallas5cowns
Members-
Content Count
42 -
Joined
-
Last visited
About dallas5cowns
-
Rank
Member
-
I don't know if a 5700BHS is the same, if it is, will temporarily removing bypass from system allow auto EQ setting to be loaded?
-
AVH-X5600BHS and AVH-X3600BHS Firmware Update
dallas5cowns replied to jegonzo3's topic in Pioneer AVH Series
Trying to run this update, 45 minutes later it's still a blank screen. How long should this take? AVH-X5700BHS Thanks, Clint -
Z120 upgraded to Z130: bypass doesn't work?
dallas5cowns replied to bones302's topic in Problems/Troubleshooting
Working now in original location.... What can I say, you're right again. -
Z120 upgraded to Z130: bypass doesn't work?
dallas5cowns replied to bones302's topic in Problems/Troubleshooting
okay, then I don't understand why the bypass is no longer working. As soon as I hit 5MPH I get the message that the parking brake is not properly connected, but the connection status shows the parking brake is "ON". I understand the harness is the same, but are the wires in the same position? Does the mute wire go to the same pin location and then to ground? -
Z120 upgraded to Z130: bypass doesn't work?
dallas5cowns replied to bones302's topic in Problems/Troubleshooting
This thread would seem to indicate that the harnesses are different, http://avic411.com/i...130bt-bypassed/ So where does the mute pin need to move to on a 110 to 130? -
Z120 upgraded to Z130: bypass doesn't work?
dallas5cowns replied to bones302's topic in Problems/Troubleshooting
I have the exact same issue after the upgrade. -
Recently my unit has begun shutting down the active application all by itself. In order to reactivate, i have to restart (HD Radio for example), turn it off manually, and then turn it on again. Turning on the second time returns audio signal to the amps. I have verified that the amps are turned on during the entire process. Any ideas? I was finally getting around to installing the 130 upgrade and now I'm concerned that I might create other problems, or might the upgrade be a solution?
-
Z120BT Bypass: Same Issue, Different Question
dallas5cowns replied to Mister Murse's topic in Problems/Troubleshooting
Had the same issue. Make sure that plug that has the parking brake wire is plugged in securely. I took my unit out and pressed all the connections together, heard a little "click" when I pressed this block and everything has been good since then. -
Won't read SD after upgrade
dallas5cowns replied to dallas5cowns's topic in Problems/Troubleshooting
Anyone else having ths issue??? -
Is there a special procedure for the full reset, or just a complete power disconnect? Yeah, as far as the iPod goes, everything was working fine prior to the upgrade and the iPod works fine when not connected to the Z120.
-
Since the upgrade from the Z110 I can no longer change the station presets, I'm stuck with the stations that were programmed prior to the upgrade. I also just installed XM and I can't change or program those presets. Anyone have solution for this? Second issue, IPOD looks like it's playing but there's no audio. Suggestions? Is anyone else having issues with the upgrade?
-
Like the title says, installed the Z120 upgrade and now a SD card that I had previously used for custom POI's no longer works. When I insert the card I get an error that says the card is not in a valid format. Any suggestions?
-
If re-pairing doesn't work then I would remove the phone from the list on the Pioneer and also remove Pioneer from phone, and then reinstall all.
-
You're advising this eventhough the instructions specifically state to perform update on disk #1 BEFORE the update on disk #2????
-
its on pioneer's site dude http://www.pioneerelectronics.com/PUSA/ ... 20BT?tab=D just download it Dude, I guess one of us can't read.. You'll notice I was referencing the manual for the UPGRADE, not the unit itself. Your link takes me to the owner's manual for the 120. Thanks for trying... I just installed without, guess it wasn't that big of a deal.