Jump to content
AVIC411.com
bradford

Traffic Shortcut

Recommended Posts

Hi,

 

Im running the latest 3.0 firware on an AUS F900BT unit.

 

I want to create a traffic shortcut on the nav screen similar to those found in the hybrid/complete mod packs.

 

 

Is someone able to give me the code needed just to put this traffic shortcut in rather than tryiny to install the entire mod?

Share this post


Link to post
Share on other sites
Can someone confirm if this will work.

 

If i place this on the navigatemap.ui and place the referenced image in 800x400

 

;TMC

 

it should work, the only thing is you should rename the BMP to whatever button you want to use or just grab the BMP from my mod

Share this post


Link to post
Share on other sites

I updated my data.zip and loaded it on the unit.

 

Unit is now stuck on "System Startup in progress, please wait" - I can use everything except GPS

 

Did i create the ZIP incorrectly, am i missing files?

 

Can someone please let me know ASAP

Share this post


Link to post
Share on other sites
Can someone confirm if this will work.

 

it should work, the only thing is you should rename the BMP to whatever button you want to use or just grab the BMP from my mod

 

Can you post the BMP from your mode? there are so many modes here... there are so many modes on this sites, not sure which one is which one...

Share this post


Link to post
Share on other sites
I updated my data.zip and loaded it on the unit.

 

Unit is now stuck on "System Startup in progress, please wait" - I can use everything except GPS

 

Did i create the ZIP incorrectly, am i missing files?

 

Can someone please let me know ASAP

 

you might be missing the BMP

Share this post


Link to post
Share on other sites

Ok so i have worked out the coding however two things.

 

1) What does #2 at the end point to?

 

BUTTON btnNMB_TMC_onmap bmp="IDT_onmap_TMC.bmp#2

 

2) I created this image i want to replace it instead of using the TMC icon from IDT.

 

here is the picture - besides chaning the name is there anything special that needs to happen to the icon for it to work (Transparent etc etc?)

 

 

Excuse the amateur attempt, never done reflections or 3D work

 

post-38500-12872759892816_thumb.jpg

Share this post


Link to post
Share on other sites
Ok so i have worked out the coding however two things.

 

1) What does #2 at the end point to?

 

BUTTON btnNMB_TMC_onmap bmp="IDT_onmap_TMC.bmp#2

 

2) I created this image i want to replace it instead of using the TMC icon from IDT.

 

here is the picture - besides chaning the name is there anything special that needs to happen to the icon for it to work (Transparent etc etc?)

 

 

Excuse the amateur attempt, never done reflections or 3D work

 

[attachment=0]746_32K_MN-665_32b copy.jpg[/attachment]

 

1) #2 means that the bmps has two sections (active/inactive, pressed/unpressed, etc), so lets say you want to make the image that you used to become grey when pressed, then your BMP should look like two images (refer to the image i used)

 

2) change the BMP used (in this case IDT_onmap_TMC.bmp#2) with the filename of the BMP you want to use

Share this post


Link to post
Share on other sites
Ok so i have worked out the coding however two things.

 

1) What does #2 at the end point to?

 

BUTTON btnNMB_TMC_onmap bmp="IDT_onmap_TMC.bmp#2

 

2) I created this image i want to replace it instead of using the TMC icon from IDT.

 

here is the picture - besides chaning the name is there anything special that needs to happen to the icon for it to work (Transparent etc etc?)

 

 

Excuse the amateur attempt, never done reflections or 3D work

 

[attachment=0]746_32K_MN-665_32b copy.jpg[/attachment]

 

1) #2 means that the bmps has two sections (active/inactive, pressed/unpressed, etc), so lets say you want to make the image that you used to become grey when pressed, then your BMP should look like two images (refer to the image i used)

 

2) change the BMP used (in this case IDT_onmap_TMC.bmp#2) with the filename of the BMP you want to use

 

Using Cs3 - How do i make a section active/inactive?

Share this post


Link to post
Share on other sites

Using Cs3 - How do i make a section active/inactive?

 

create a new image withe the width of your desired button and the length being twice the length of your desired button, copy your image to the new one and place it on the upper part, now make your original image black and white and then copy it and paste it on the new image and now place it on the bottom part, close your orig image and don't save it, save your newly created image to a filename that you prefer and then put that in your 800_480 folder and change the BMP name on the script to the filename of your new BMP

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×