Chygayster Posted December 15, 2016 Report Share Posted December 15, 2016 Need help AVH X8650BT AVIC5000NEX My internal SDcard died I took a friend's card of this same device. Once everything worked fine. I do not know what happened but when you return the card to the device of my friend is not a device should be loaded. I think I had included COPY DEVICE MODE, and it killed the second Sdcard. What to do? How to restore the card, or where to get the image of the SD card Quote Link to post Share on other sites
Chygayster Posted December 15, 2016 Author Report Share Posted December 15, 2016 MX6SDL JUPITER KT 4.2.2 U-Boot > bsp getBSP A is validBSP B is valid## A Side BSP Information: Magic Number :0xa55a5aa5(a55a5aa5:Valid, other:Invalid) Boot Mode :0x00000000(0:Normal, 1:Recovery, 2:EasyRecovery, 3:Re-EasyRecovery, default:Normal) Launch Mode :0x00000003(0:APL, 1:TestMode.apk, 2:Slave TestMode, 3:Boot Error, default:APL) TestMode Sub-Mode :0x00000000(0:TextMode_A.key, 1:Serv Mode, 2:Tech Mode, default:Tech Mode) Bootimage Side :0x00000000(0:Side A, 1:Side B, default:Side A) Recoveryimage Side :0x00000000(0:Side A, 1:Side B, default:Side A) Debug Switch :0x00000000(0:OFF, 1:ON, default:OFF) Usb OTG Switch :0x00000000(0:Host, 1:Device, default:Host) Memchk flag :0x00000000(0:No, 1:Yes, default:No) Warp boot :0x00000000(0:Side A, 1:Side B, default:Side A) Boot Sub-Mode :0x00000000(0:Normal, 1:Catch snapshot, 2:Warp, default:Normal) Update flag :0x00000000(0:Recovery-Update, 1:uboot update, 2:boot.img update, 3:recovery.img update, 4:system.img update, 5:opening data update, 6:UI update, 7:All image update, 8:TESTMODE_N.KEY, 9:easyrecovery copy, a:easyrecovery copy&verify, b:password key copy&verify, c:easyrecovery mode change, default:Recovery-Update) Update sub-flag :0x00000000(0:SD Card, 1:USB1, 2:USB2 default:SD Card) UI Update flag :0x00000000(0:non-updating, 1:updating, default:non-updating) Reserved1 flag :0xffffffff(default:0xFFFFFFFF) Reserved2 flag :0xffffffff(default:0xFFFFFFFF)## B Side BSP Information: Magic Number :0xa55a5aa5(a55a5aa5:Valid, other:Invalid) Boot Mode :0x00000000(0:Normal, 1:Recovery, 2:EasyRecovery, 3:Re-EasyRecovery, default:Normal) Launch Mode :0x00000003(0:APL, 1:TestMode.apk, 2:Slave TestMode, 3:Boot Error, default:APL) TestMode Sub-Mode :0x00000000(0:TextMode_A.key, 1:Serv Mode, 2:Tech Mode, default:Tech Mode) Bootimage Side :0x00000000(0:Side A, 1:Side B, default:Side A) Recoveryimage Side :0x00000000(0:Side A, 1:Side B, default:Side A) Debug Switch :0x00000000(0:OFF, 1:ON, default:OFF) Usb OTG Switch :0x00000000(0:Host, 1:Device, default:Host) Memchk flag :0x00000000(0:No, 1:Yes, default:No) Warp boot :0x00000000(0:Side A, 1:Side B, default:Side A) Boot Sub-Mode :0x00000000(0:Normal, 1:Catch snapshot, 2:Warp, default:Normal) Update flag :0x00000000(0:Recovery-Update, 1:uboot update, 2:boot.img update, 3:recovery.img update, 4:system.img update, 5:opening data update, 6:UI update, 7:All image update, 8:TESTMODE_N.KEY, 9:easyrecovery copy, a:easyrecovery copy&verify, b:password key copy&verify, c:easyrecovery mode change, default:Recovery-Update) Update sub-flag :0x00000000(0:SD Card, 1:USB1, 2:USB2, default:SD Card) UI Update flag :0x00000000(0:non-updating, 1:updating, default:non-updating) Reserved1 flag :0xffffffff(default:0xFFFFFFFF) Reserved2 flag :0xffffffff(default:0xFFFFFFFF)MX6SDL JUPITER KT 4.2.2 U-Boot > Quote Link to post Share on other sites
Chygayster Posted December 15, 2016 Author Report Share Posted December 15, 2016 U-Boot 2009.08 (Jan 06 2014 - 16:32:44)CPU: Freescale i.MX6 family TO1.1 at 792 MHzThermal sensor with ratio = 182Temperature: 30 C, calibration data 0x5834d27dmx6q pll1: 792MHzmx6q pll2: 528MHzmx6q pll3: 480MHzmx6q pll8: 50MHzipg clock : 66000000Hzipg per clock : 66000000Hzuart clock : 80000000Hzcspi clock : 60000000Hzahb clock : 132000000Hzaxi clock : 198000000Hzemi_slow clock: 99000000Hzddr clock : 396000000Hzusdhc1 clock : 198000000Hzusdhc2 clock : 198000000Hzusdhc3 clock : 198000000Hzusdhc4 clock : 198000000Hznfc clock : 24000000HzBoard: i.MX6DL/Solo-JUPITER: unknown-board Board: 0x61011 [POR ]Boot Device: NORI2C: readyDRAM: 1 GBFlash: 8 MBMMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2Using default environmentIn: serialOut: serialErr: serial***** display DDR calibration result ********************************************Display result(register) of WriteLeveling MMDC registers updated from WriteLeveling MPWLDECTRL0 (0x021b080c) = 0x00310037 MPWLDECTRL1 (0x021b0810) = 0x0019001B***************************************Display result(register) of DDR calibration MMDC registers updated from calibration Read DQS Gating calibration MPDGCTRL0 PHY0 (0x021b083c) = 0x42210215 MPDGCTRL1 PHY0 (0x021b0840) = 0x016F0170 Read calibration MPRDDLCTL PHY0 (0x021b0848) = 0x4A474D49 Write calibration MPWRDLCTL PHY0 (0x021b0850) = 0x42403F41***************************************Net: got MAC address from IIM: 00:00:00:00:00:00FEC0 [PRIME]. doneErased 1 sectorsCopy bsp side A to B success!BSP A is validimx6 core num: 1BSP A is validBSP B is validmatch invalid password 2.main loop boot env = run bootargs;booti mmc1 ${bootpartition}Hit any key to stop autoboot: 0mmc1 init failedboot error, will boot easyrecovery!!BSP A is validBSP B is valid-launch mode. doneErased 1 sectors. doneErased 1 sectorsboot easyrecovery !!main loop boot env = run bootargs;booti ${bootaddr}Hit any key to stop autoboot: 0kernel @ 10808000 (2829424)ramdisk @ 11800000 (877890)kernel cmdline: use uboot command line: console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 nosmp video=mxcfb0:dev=ldb,bpp=32 video=mxcfb1:dev=ak8814,BT656-NTSC,if=BT656,bpp=32 video=mxcfb2:off fbmem=6M,6M vmalloc=400M androidboot.hardware=freescale arm_freq=800 printk.time=1 printk_console=offStarting kernel ...Uncompressing Linux... done, booting the kernel.# Quote Link to post Share on other sites
asd255 Posted December 15, 2016 Report Share Posted December 15, 2016 You should have read the topic - The AVIC Development Mod NEVER ENTER COPY DEVICE MODE, YOU WILL BRICK YOUR DEVICE! ПоздравлÑÑŽ - you have 2 bricks Quote Link to post Share on other sites
Chygayster Posted December 15, 2016 Author Report Share Posted December 15, 2016 СпаÑибо ... Ñ Ñто уже понÑл... придетьÑÑ Ð¿Ð¾ÐºÑƒÐ¿Ð°Ñ‚ÑŒ флешки? И перед инÑталÑцией SDcard начала через UART вернуть наÑтройки BSP в нули? Quote Link to post Share on other sites
Chygayster Posted December 15, 2016 Author Report Share Posted December 15, 2016 Thanks ... I already knew ... I have to buy a flash drive? And before beginning installation SDcard via UART return BSP settings to zero? Quote Link to post Share on other sites
Chygayster Posted December 15, 2016 Author Report Share Posted December 15, 2016 Just i place it drive without checking the settings BSP U-Boot. Then I realized that hastened. Maybe easier to buy an image SDcard as I understand an existing SDcard can I copy? Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.