ibeb

I have had my D3 for many years and have had it hooked up to numerous phones without problems, until now. It worked fine for both calls and audio for my iPhone 3g and my wife's 4, but now that I have the 4s it will only work for audio? It connects without problems, I can use the controls to control both Pandora and my music on the phone via bluetooth, but not in or out audio when making calls. It shows up as connected, will switch from whatever mode it is in to phone mode if either an inbound call is coming or I initiate a call on my phone, but then I have to switch my phone to speakerphone to

Did you get anywhere on this? I have and AVIC-D3 in my 06 F150 and have for many years with no porblems. It has worked bluethooth with other cellphones, my iPhone 3G, my wife's iPhone 4, but now that i have my iPhone 4S I'm having issues. It works great to bluetooth the music, but doesn't work at all for calls? If I'm getting an inbound call the mode and screen will change, but when I answer it I can't hear them and they can't hear me - I end up having to switch to speaker phone on my iPhone. It worked a couple times when I first got the new phone, but as soon as I tried to use Siri it stopped

Either that, or just call and cancel. That is what I did and declined their first 2 offers to continue service and went with the 3rd at 3.99/mo for 6 months I think. When I get close to the end of that, I will just call back and cancel again. Erik

Thanks for the response. Was doing some searching and found a couple other posts that said that I should, but nothing recent and some said that they were only able to get a smaller range of channels. Thanks agian - Erik

I just picked up an 06 F150 King Ranch that had the factory sirius radio. I have the Avic-D3 and the XM unit and installed it the other day from my 04 F150. Previously I had been using the antenna that came with the pioneer xm unit and did not have any problems, and cancelled my xm service a while back because I never listen to the radio and primarily use my iPod for music. When putting the system in my new truck I decided to install all the components in case I change my mind down the road and was able to plug the stock sirius antenna into the pioneer xm unit (just removed the plastic plug

Not AVIC related, but does nayone know the correct cable to get so that my wife can use her iPod through her factory Honda Pilot stereo? It is an 06 with the 6 disc in-dash changer and XM. I have seen a few and some say that you have to disable the XM and others say that they will work, but will not display info unless the XM is disabled, some say the steering wheel controls will still work, but don't want to spend $100 on one that is a POS. thanks - Erik

VBLUE - last question. will this cig adaptor work? just want ot make sure that it has the right voltage output. thanks - erik http://cgi.ebay.com/car-Charger-BELKIN- ... 240%3A1317

I have an 04' F150 and used the Metra kit from the local circuit city. I don't think that they changed anything. Erik

duplicate

I have the LG VU 915 with AT&T and was able to pair it up to my D3 without any problems. It works for making/receiving calls, but won't transfer the phone book (something that AT&T has disabled). The only thing that I had to change on my phone to get it to sync was to make it visible in the bluetooth settings. Now whenever I get close to my truck and the stereo is on it will sync - it even has the range to synce inside the house when I use my remote start on the cold mornings. Erik

VBLUE - Could you post a link to what you are talking about? Since this will be in the dash, I may be able to cannibalize it and hardwire it in behind the stereo to a switched power. Thanks - Erik

CamelTow - Thanks for the response. I already have the Pioneer iPod cable hooked up and will probably run the Appple one too. I will just hook up the Apple cable for video through the back of the deck and then run the pioneer cable when I am just listening to music. Not being able to control the video through the head unit isn't that big of a deal since the CD-I200 wouldn't do that anyways. Thanks - Erik

If that doesn't work, will this work to hook up to the back of the D3 - http://store.apple.com/us/product/MB129#overview I have read that it will work for firmware 2.0 and older, but not 2.1. When I go into the settings mode of my iPod it says version 2.0.1 Thanks for any help - Erik

Does anyone know if this cable will work to get the video from my iPod to the D3 through the front aux port? http://www.pioneerelectronics.com/PUSA/ ... s/CD-V150M I can run that for video and the CD-I200 for the music if it will work. Thanks - Erik

I have had my D3 for a while and finally got an iPod to use for music and video playback to free up the dvd slot for nav. The cable arrived today and took a whole 5 minutes to pull the deck and hook it up and re-install the deck. Hooked the cable to the iPod and have normal controls over the sound and all works great. Set the iPod to video out and when I hit the video button on the D3 I just got the normal message to control unit from iPod. Tabbed through the menu on the iPod and started a video and got nothing - no sound or picture on the D3 and a message on the iPod that it needed to be