Need help AVH X8650BT AVIC5000NEX
My internal SDcard died
I took a friend's card of this same device. Once everything worked fine. I do not know what happened but when you return the card to the device of my friend is not a device should be loaded.
I think I had included COPY DEVICE MODE, and it killed the second Sdcard.
What to do? How to restore the card, or where to get the image of the SD card
MX6SDL JUPITER KT 4.2.2 U-Boot > bsp get
BSP A is valid
BSP B is valid
## A Side BSP Information:
Magic Number :0xa55a5aa5(a55a5aa5:Valid, other:Invalid)
Boot Mode :0x00000000(0:Normal,
1:Recovery,
2:EasyRecovery,
3:Re-EasyRecovery,
default:Normal)
Launch Mode :0x00000003(0:APL,
1:TestMode.apk,
2:Slave TestMode,
3:Boot Error,
default:APL)
TestMode Sub-Mode :0x00000000(0:TextMode_A.key, 1:Serv Mode, 2:Tech Mode, default:Tech Mode)
Bootimage Side :0x00000000(0:Side A, 1:Side B, default:Side A)
Recoveryimage Side :0x00000000(0:Side A, 1:Side B, default:Side A)
Debug Switch :0x00000000(0:OFF, 1:ON, default:OFF)
Usb OTG Switch :0x00000000(0:Host, 1:Device, default:Host)
Memchk flag :0x00000000(0:No, 1:Yes, default:No)
Warp boot :0x00000000(0:Side A, 1:Side B, default:Side A)
Boot Sub-Mode :0x00000000(0:Normal, 1:Catch snapshot, 2:Warp, default:Normal)
Update flag :0x00000000(0:Recovery-Update,
1:uboot update,
2:boot.img update,
3:recovery.img update,
4:system.img update,
5:opening data update,
6:UI update,
7:All image update,
8:TESTMODE_N.KEY,
9:easyrecovery copy,
a:easyrecovery copy&verify,
b:password key copy&verify,
c:easyrecovery mode change,
default:Recovery-Update)
Update sub-flag :0x00000000(0:SD Card, 1:USB1, 2:USB2 default:SD Card)
UI Update flag :0x00000000(0:non-updating, 1:updating, default:non-updating)
Reserved1 flag :0xffffffff(default:0xFFFFFFFF)
Reserved2 flag :0xffffffff(default:0xFFFFFFFF)
## B Side BSP Information:
Magic Number :0xa55a5aa5(a55a5aa5:Valid, other:Invalid)
Boot Mode :0x00000000(0:Normal,
1:Recovery,
2:EasyRecovery,
3:Re-EasyRecovery,
default:Normal)
Launch Mode :0x00000003(0:APL,
1:TestMode.apk,
2:Slave TestMode,
3:Boot Error,
default:APL)
TestMode Sub-Mode :0x00000000(0:TextMode_A.key, 1:Serv Mode, 2:Tech Mode, default:Tech Mode)
Bootimage Side :0x00000000(0:Side A, 1:Side B, default:Side A)
Recoveryimage Side :0x00000000(0:Side A, 1:Side B, default:Side A)
Debug Switch :0x00000000(0:OFF, 1:ON, default:OFF)
Usb OTG Switch :0x00000000(0:Host, 1:Device, default:Host)
Memchk flag :0x00000000(0:No, 1:Yes, default:No)
Warp boot :0x00000000(0:Side A, 1:Side B, default:Side A)
Boot Sub-Mode :0x00000000(0:Normal, 1:Catch snapshot, 2:Warp, default:Normal)
Update flag :0x00000000(0:Recovery-Update,
1:uboot update,
2:boot.img update,
3:recovery.img update,
4:system.img update,
5:opening data update,
6:UI update,
7:All image update,
8:TESTMODE_N.KEY,
9:easyrecovery copy,
a:easyrecovery copy&verify,
b:password key copy&verify,
c:easyrecovery mode change,
default:Recovery-Update)
Update sub-flag :0x00000000(0:SD Card, 1:USB1, 2:USB2, default:SD Card)
UI Update flag :0x00000000(0:non-updating, 1:updating, default:non-updating)
Reserved1 flag :0xffffffff(default:0xFFFFFFFF)
Reserved2 flag :0xffffffff(default:0xFFFFFFFF)
MX6SDL JUPITER KT 4.2.2 U-Boot >
U-Boot 2009.08 (Jan 06 2014 - 16:32:44)
CPU: Freescale i.MX6 family TO1.1 at 792 MHz
Thermal sensor with ratio = 182
Temperature: 30 C, calibration data 0x5834d27d
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 99000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
nfc clock : 24000000Hz
Board: i.MX6DL/Solo-JUPITER: unknown-board Board: 0x61011 [POR ]
Boot Device: NOR
I2C: ready
DRAM: 1 GB
Flash: 8 MB
MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
Using default environment
In: serial
Out: serial
Err: serial
***** display DDR calibration result *****
***************************************
Display result(register) of WriteLeveling
MMDC registers updated from WriteLeveling
MPWLDECTRL0 (0x021b080c) = 0x00310037
MPWLDECTRL1 (0x021b0810) = 0x0019001B
***************************************
Display result(register) of DDR calibration
MMDC registers updated from calibration
Read DQS Gating calibration
MPDGCTRL0 PHY0 (0x021b083c) = 0x42210215
MPDGCTRL1 PHY0 (0x021b0840) = 0x016F0170
Read calibration
MPRDDLCTL PHY0 (0x021b0848) = 0x4A474D49
Write calibration
MPWRDLCTL PHY0 (0x021b0850) = 0x42403F41
***************************************
Net: got MAC address from IIM: 00:00:00:00:00:00
FEC0 [PRIME]
. done
Erased 1 sectors
Copy bsp side A to B success!
BSP A is valid
imx6 core num: 1
BSP A is valid
BSP B is valid
match invalid password 2.
main loop boot env = run bootargs;booti mmc1 ${bootpartition}
Hit any key to stop autoboot: 0
mmc1 init failed
boot error, will boot easyrecovery!!
BSP A is valid
BSP B is valid
-launch mode
. done
Erased 1 sectors
. done
Erased 1 sectors
boot easyrecovery !!
main loop boot env = run bootargs;booti ${bootaddr}
Hit any key to stop autoboot: 0
kernel @ 10808000 (2829424)
ramdisk @ 11800000 (877890)
kernel cmdline:
use uboot command line:
console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 nosmp video=mxcfb0:dev=ldb,bpp=32 video=mxcfb1:dev=ak8814,BT656-NTSC,if=BT656,bpp=32 video=mxcfb2:off fbmem=6M,6M vmalloc=400M androidboot.hardware=freescale arm_freq=800 printk.time=1 printk_console=off
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
#
NEVER ENTER COPY DEVICE MODE, YOU WILL BRICK YOUR DEVICE!
ПоздравлÑÑŽ - you have 2 bricks
СпаÑибо ... Ñ Ñто уже понÑл... придетьÑÑ Ð¿Ð¾ÐºÑƒÐ¿Ð°Ñ‚ÑŒ флешки? И перед инÑталÑцией SDcard начала через UART вернуть наÑтройки BSP в нули?
Thanks ... I already knew ... I have to buy a flash drive? And before beginning installation SDcard via UART return BSP settings to zero?
Just i place it drive without checking the settings BSP U-Boot. Then I realized that hastened.
Maybe easier to buy an image SDcard as I understand an existing SDcard can I copy?