xiplare

USB problem: Resolved (format FAT32 the USB key and now run OK)

The divx from USB cause many jumps, any solution?

Hello,

Once installed Avicnet in EU dispositive I have the following problems are likely solution:

1 - The USB device is not recognized by the system (as if the key is not connected)

2 - Avicnet does an automatic reboot if I start (even, with inserted SD and without)

3 - Avicnet performed mute the car radio (even without running Primo), and do not activate it again (with Pioneer v2.07 I could hear the car radio and when the GPS speak the radio sound is muted, then continue the radio. When I was listening to the radio or USB or SD, GPS mute the music to speak). Not now, whenever I boot AVICNET radio is muted. (and the GPS speak over SD music - This is not a problem ) ¿?

I still use Primo 1.2 incorporate in Avicnet, is posible that Primo 1.0 (post 2) be the solution?

4 - adjustment of pioneer (not avicnet) MUTE button is inactive

And is it possible to use a USB phone as a modem? How? (nokia c6-01)

Thank for your contributions, and excuse me for mi bad english (I´m spanish)



Hello,

Thanks to your suggestions I managed to start Avicnet:

I started in v2.07 and upgrade to V3.0 (with checksum error, the system would not start), then upgrade to V3.02 pioneer, and finally install AVICNET. Apparently the system boots, but even I have some problems:

The message "AVIC. The sistem is starting. Please wait" does not end

When start maps button or destinate the system back a message "Mapes out of date" and dont allow me to continue.

Any solution?

I am Spanish and I apologize for my grammatical errors

Help!!!!

I followed the instructions to update WinCE version 2.0070000 to 3.0 (on my F500BT Europe) to install the update after 3.02 of pioneer europe:

During the upgrade to 3.0 gives an error (checksummed error) but finally says UPDATE OK, but after reboot the screen goes black and the LED flashes. I can not boot the system or TestMode ....

What can I do? Is posible go back to version CE2.07?

Help!!!!

I followed the instructions to update WinCE version 2.0070000 to 3.0 (on my F500BT Europe) to install the update after 3.02 of pioneer europe:

During the upgrade to 3.0 gives an error (checksummed error) but finally says UPDATE OK, but after reboot the screen goes black and the LED flashes. I can not boot the system or TestMode ....

What can I do? Is posible go back to version CE2.07?

Hello,

I tried Avicnet EnglishEU and Avicnet Italian in my F500BT (WINCE5, version 2.0070000) but not get it to work.

In both cases I have the same problem, the system does not start (only see the boot screen but do not get to see "starting system").

You give me some idea? Is it necessary to upgrade WINCE? How F500BT is updated (WINCE)?

Thank you all for your work

Hola,

En primer lugar agradeceros a todos los esfuerzos por mantener un foro tan interesante y ademas en español

Tengo un F500BT y muchas dudas, mi aparato trae la vesion 2.07 y mapas 1.xxxx (no me acuerdo), la cuestion es que quiero actualizarlo con los foiciales de la casa pero no los reconoce, es deicr,

Al actualizar a 2007000 no lo reconoce (creo que esto es normal ya que es la version que tengo ¿no?)

al actualizar a 3022000 tampoco lo reconoce y no comienza la instalacion ¿Tengo que instalar esta ¿no?

al actualizar a 4001000 si la reconoce y comienza la instalación pero lo he parado porque no me atrevo a pasar directamente de 2007000 a 4001000 ¿Se puede hacer directamente o hay que pasar primero por la 3022000?

No se, estare haciendo algo mal seguramente, aunque en todos los casos sigo los mismos pasos y solo parece activarse la actualizacion 4001000

Por otra parte estuve mirando el hilo http://avic411.com/index.php?/topic/32763-english-avicnet-for-avic-f-series/ y parece muy muy interesante, pero mi ingles deja mucho que desear y no se si funcionara en los equipos europeos, ni si funcionaran correctamente los demas elementos (camara trasera, bluetooth...) pero aparentemente es una maravilla, permitiendo ademas de casi cualquier navegador otras aplicaciones como internet, obdII, ...

Si alguno de los foreros (que sepa mas ingles que yo) se anima a comentarlo un poquito pero en español es posible que nos interese.

Gracias a todos por vuestro esfuerzo, y si me ayudais con el tema de las actualizaciones pues doble de gracias