Jump to content

Search the Community

Showing results for tags 'Update Failed'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Announcements
    • Welcome/Site News
    • Custom Backgrounds
  • Pioneer AVIC Navigation Units
    • NEX Series
    • Z Series
    • X Series
    • F Series
    • D Series
    • N Series
    • AppRadio, AppRadio 2, AppRadio 3
    • AVIC-U310BT
  • System Add-Ons
    • General
    • XM/Sirius/HD Radio and Traffic Receivers
  • Other Discussions
    • Off-Topic
    • Vehicle Specific Wiring
    • Security/Stolen AVIC's
    • Classifieds (Buy/Sell/Services)
    • Archive


  • Official AVIC411 Blog
  • Popular Topics
  • gadgeeets' Blog
  • Gmane's Blog
  • joirico27's Blog
  • Double's Blog
  • trailer's Blog
  • pimpcee1981's Blog
  • kodunmit's Blog
  • moses' Blog
  • bharper351's Blog
  • cjmccarthy12's Blog
  • jimbocorvette's Blog
  • ayother's Blog
  • Tluda
  • sandjieuw's Blog
  • TI 3VOM's Blog
  • imgizzy's Blog
  • avic 910bt bluetooth issue
  • riderdog's Blog
  • riderdog's Blog
  • avalanchegroup's Blog
  • avalanchegroup's Blog
  • AVIC X930BT
  • jacks1872001's Blog
  • Ashante503's Blog
  • manugude's Blog
  • Vollgatter's Blog
  • poisidon33298's Blog
  • raincitydj's Blog
  • jadamache's Blog

Found 1 result

  1. Hello All, First post here...so let me know if this needs to go somewhere else. TL;DR: I got my unit to boot back into the OS after step 3 of this thread, but it still fails to update the firmware when I try. My 7000NEX was still running FW version 1.012. I decided to update the firmware to 1.15. I downloaded the file, read the instructions, formatted the flash drive, turn off AV source...basically tried to be a good boy and follow the instructions. My unit read the USB key, notified me that I was upgrading from 1.012 to 1.15...I confirmed by clicking on Continue. I was eventually prompted to reset the device, which I did, but when I reset it, I disconnected both the ACC and PWR wires. Upon powering back on, it went to a screen that said "Reading...", then to a screen saying "Update Failed!" "Press HOME to continue" At this point...I got stuck. I tried multiple flash drives, redownloaded the file from pioneer's website...All I could get it to do was say "Update Progress,,," and "version 1.01 to 1.01" even though my USB key had the 1.15 firmware on it, then it would go back to "Update Failed!" Anyway, I decided to dig deeper and try to find a custom ROM that I could hopefully just push onto this thing and found this thread. Obviously this is a treasure trove of information but I'm still stuck. From that thread, I followed steps 1, 2, and 3...(e.g. backup my NOR, BSP, and SD Card) using the Script Mode instructions. After step three though, my unit FINALLY BOOTED BACK UP INTO THE OS!!!! At first I was super ecstatic and thought "Great! Now I can try to update my firmware again and not make the same mistake!". WRONG... Now when I go through the instructions, and try to update the firmware...I get to the confirmation screen, it shows the right firmware jump, but it immediately goes to a "Update Failed!" screen again as soon as I confirm. I haven't tried other FW versions like 1.06, 1.08, 1.10, 1.14...though I do have the files. I'm just trying to figure out what I should do next? In the Test Mode that the USB key from the linked thread, there are functions like Write Bootloader, Write Programs, etc... and i'm wondering if I can use those to clear or fix whatever's still corrupt under the hood to allow any firmware update? Anyone have any clues?