milespjking
-
Content Count
15 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Posts posted by milespjking
-
-
I tried as RonS proposed but nothing worked so far
I updated my unit to 6.0
then I figured there is no way I could install the "ipod settings" on the firmware
when i tried it i was stuck in the "program foreced write" step.
my ucom version was 8.12 and ucom version i got from the 5.1 firmware just showing me --.------ rather than 8.05
I tried formating my two different sd cards mutiple times but still.
so i re install firmware 5.0 again.
then I tried 5,1 firmware and it was looking good
showing me copying some files as you updating firmware.
until the "program forced write" step
still it was same as i stated above.
after that when I lookeed in to my service information
it says firmware version is 5.0
application version is 5.1
but no "ipod settings"
then I tried to roll back my firmware with RonS' idea
it did roll back my firmware to firmware version is 5.0
application version is 5.0
and I tried to install 5.1 into my unit
then this again 'stuck in the "program foreced write" step.
my ucom version was 8.12 and ucom version i got from the 5.1 firmware showing me --.------ rather than 8.05'
now I am trying to reinstall firmware 4.0 with fingercrossed
-
Yes. You should be able to revert to the previous version (the active PRG directory) by creating or deleting /USER/PRG.FLG. Also, it usually is a good idea to make a backup of /USER on to SD before making any changes. However you can always create a new PRG.FLG since it is just an empty file.
I haven't tried it yet
I will try it later in the day
and get back to the forum
-
Did you try using the PRG.FLG file to toggle back to the previous version stored in the alternate /USER/PRG directory tree? If it works you should be able to install the appropriate iPod support patch. Then re-install v 6.0
Thank you for the head up
and I have sincere appreciation for your devotion to this forum
the method you talking is this?
-
be careful if you want to use this update with cd-IV202NAVI for lightning cable connectivity
don't update your unit with this map before you read chapter. 6 of this link
if your firmware is 4.0 then update it to 4.6
if your firmware is 5.0 then update it to 5.1
or you will never be able to get the menu "ipod settings" in your avic for fully functional iphone 5 or higher connection
i updated my unit to firmware 6.0 without thinking enough
Sadly I can not find any possible solution to use my iphone 5s in my car
now i ended up spending extra $70 for nothing
don't make the same mistake i made
-
Dear Vinweasel.
I am in S.Korea and using z110bt.
let me know if there is something I can help.
-
nadnava
read this post
it might help you
http://avic411.com/index.php?/topic/33505-jailbreak-appradio-appradio-plus/
-
this is how I run an alternative navigation on my z110bt
(this link is not mine, I looked it up on the web)
Ive tried Pioneerus but for me this is better off
there is also a different way
http://avic411.com/index.php?/topic/34188-appradio-extensions-20-beta-full-iphone-control/
worth to read
good luck
-
Is it software for Windows CE? and it should at least work on ARM CPUs.
yes it works in Window CE 6.0
I will look it up about ARM CPU
frankly, I have no programming skill.
I just took a C++ class in the college back in the days
I am just googling everything now.
-
Ok what navigation software do you have with your local map?
thank you for your attention
but I dont think you ever heard of it.
it is called "Mappy"
-
Ive just figured the problem 1 happens on and off
anyway, I will use my nav system when my engine is turned on, it would not be a big dealand I got igo8.3 maps, just checked it Igo working good on pioneerusnow, here's thingI am living in the country igo doesn't supportand I have a local map, tried boot it up via pioneerus.I edited pioneerus.cfg by notepad to designate a folder to where the local nav program was.I have failed tho.can you give me tips for it? -
I just reinstalled pioneerus
now it works fine.
Edit:at the first trial, it worked it was supposed to work
at the second trial, I ran into the same problem as I mentioned in earlier post(problem 1)
just wondering that when I tried to launch igo8it just shows the booting screen of Igo8 and then goes offis it just because I dont have the map for igo8?I only have Igo8 files the developer sent to me (which does not have maps) -
Thank you ver much!!!
finally, I could get to the shell.
here are problems tho.
here is my procedure I went through
Uninstalled pioneerus
Installed CNSD-310FM for the firmware
installed pioneerus
put lic file into pioneerus folder
problem 1
I can't get to the shell when the engine is of the car is off even tho I put electricity on in the car.
when the engine is off, trying to get to the shell it just shows me black and white horizontal lines
problem 2
I can't launch Igo8 ( Actually, I am not going to use Igo since in the country I am living in, igo doesn't support the maps
I just want to try if it works fine)
I assumed it was a fault of designated folder and the name of exe file.
so I tried with igo8 Sanik provide me with, I put the igo8 folder into the pioneerus folder, didn't work
I put igo8 folder into the root, didn't work
I changed the name of igo8.exe to alien-navi.exe, didn't work.
problem 3
Buttons on the shell, nothing works
I have only 3 taps on the screens when I launch the shell
igo, navitel on the center , reset on lower left corner.
I can see why navitel does not work but I thought at least reset tap would work.
Am I missing something?
-
Install CNSD-310FM.
I am on the way
thank you very much
-
Hi there
I have been lurking on the forum ever since I've got a z110bt unit.
Ive been watching every single effort you members have made.
I wish I could join you guys. I have no programming skill tho.
I've found there is possibility to install 3rd party map into my unit
decided to move my ass little bit for my unit
I have unmodified z110bt with the firmware v 1.0000
now I got pioneerus and trying to install it into my unit
but I can not get to pioneerus shell
I have done everything accordingly.
I got lic file into pioneerus folder
then pushed home button, destination on the screen, and next track on the tray.
so,I have contacted to the developer.
He/she told me to upgrade firmware to 4.001
unfortunately, I dont know how.
I thought, at least, to do what I could do
I upgraded the firmware to 1.001 from official website.
still does not work.
could you give me any kind of headup
appreciate greatly in advance.
2015 Avic Z120 map update
in Hacks/Mods
Posted
*update*
I am using my jailbroken iphone 4 with my avic flawlessly
I want to mirror my phone to the navigation
and it works perfectly
only one problem I've got here is iphone 4 is too laggy
so I decided to use my iphone 5s and bought cd-iv202navi.
unfortunately, I haven't found any way to work with it.
However, today, I exprienced some strange behavior of my avic
even though all the hassels i went through here http://avic411.com/index.php?/topic/81643-2015-avic-z120-map-update/?p=342370
except the initial try of getting it working, I haven't connected iv202navi to the gps.
I just checked if "ipod settings" would show up in the av setting menu.
I am using my avic with firmware 5.0 now
i connected iv202navi today and checked if it would work with a iphone5s
when I connected my iphone5s to the gps
"ipod" in the av source menu did not show up (which would show up on the left side of screen when you connect ipod to the avic)
then I update firmware to 5.1
still everything looking promising until the "program foreced write" step
after this incompleted update, still no ipod setting option in the av setting menu
BUT, in the av source menu (which is left side of screen), there was ipod menu.
I didn't even connect my phone to my avic
so I connected my jailbroken iphone5s to the unit
and my iphone5s screen mirrored into the avic, also was getting charged.
then I tried my iphone7+, it mirrored into the unit, also getting charged.
but no sound.
I decided to reset the unit by disconnecting the battery. (I solved some iphone connectivity problem before with this method)
after the reset, ipod menu on the av source was gone.
I rolled back firmware to ver. 5.0 and updated to ver 5.1 a couple of times
but haven't come back.
I felt like i almost got it...
and I wonder if there is any possible way to keep the ipod menu in the av source even though iphone(ipod) is not connected to the unit?