dougleonard Posted January 21, 2013 Report Share Posted January 21, 2013 I bought an Appradio 2 that is missing the iphone cable. I am wondering if anyone would be willing to ohm out the pins. I just need the USB pins (should be 4) 5V, +D, -D, GND. I will need from the female jack to the header that connects to the radio. I have attached pictures to show some pin numbers. Thanks for any help. I hate these proprietary connectors. They have no use. They could have easily put a usb port and the RCA AV connectors for ipod on the back of the unit. Quote Link to post Share on other sites
dougleonard Posted January 21, 2013 Author Report Share Posted January 21, 2013 I am going to answer my own question and share it with you guys in case you need this info down the road. I went ahead and bought the service manual for this unit and got the pinouts from it. I soldered on my USB jack and all is good and I don't have that cord that will go bad on the unit. The picture below has the true pinout numbers and here is the key! 1 USB - 2 USB + 3 NC 4 USB 5V 5 USB GND 6 A-Return 7 LOUT 8 V-RETURN 9 NC (Apple Device Rx) 10 NC (Apple Device Detect) 11 V_RETURN 12 V_RETURN 13 Component Pb / CVBS 14 Component Y 15 Component Pr 16 ROUT 17 NC (Acc Detect) Quote Link to post Share on other sites
texbuck Posted January 22, 2013 Report Share Posted January 22, 2013 That is very cool. Where did you find the service manual for this and how much did it cost? Quote Link to post Share on other sites
dougleonard Posted January 23, 2013 Author Report Share Posted January 23, 2013 I bought it from here: Service-Manuals-Schematics.com it is $12.99 for the schematic/service manual and they send you a link to get it in your email so there is no deliveries. Quote Link to post Share on other sites
texbuck Posted January 23, 2013 Report Share Posted January 23, 2013 I see there are 2 manuals with xnew5 and xnuc suffixes. I assume that's because of us and non us models, but which one's which? Quote Link to post Share on other sites
Shadoh Posted March 4, 2013 Report Share Posted March 4, 2013 Really nice. I want to break out with the component video to a second screen. You show two pin layouts of the actual plug but the the pinout doesnt match, which one is correct? Also, I have the same question, if I buy a manual from that site which one is for the US version of the manual? The XNUC or the NEW5? Thank you Quote Link to post Share on other sites
wei803 Posted March 9, 2013 Report Share Posted March 9, 2013 Hi, me too would like to know which is the right manual to get? NVM found the answer, both link will give you same zip file contain both PDF, apparently one of it is only a amendment notice to the main manual. Quote Link to post Share on other sites
mrmees Posted April 22, 2015 Report Share Posted April 22, 2015 Hate to resurrect a years old thread but I wanted to see if either of you proud owners of the Service Manual would mind posting the pin out of the power/speaker wiring harness? I purchased an SPH-DA100 with no harness and the aftermarket selection is abysmally short on info. I've already sent one back to Amazon for missing wires. Would like to be able to confirm one while it's in my hand - but to do that I need the wiring diagram of the harness. Just my luck - this info doesn't seem to exist anywhere on the internet. Thanks! Quote Link to post Share on other sites
ravencali Posted April 3, 2016 Report Share Posted April 3, 2016 hi, where are audio pins ?? how iphone 4 send sound from ipod tu appradio2(sph-da100). need help, i`am trying to diy cables for iphone4 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.