XBinRochester

I have the same problem ever since I upgraded to 3.0

I did try changing the sys.txt and it didn't help.

I called Pioneer and they said that is the way the new system works. First she told me that "it defaults to the capital of the state", and I asked her what year our capital of NY changed from Albany to Buffalo? LOL What I do is just to the right of the default city is: HISTORY, just a touch there and you can hit your home town. Not a fix, but a quick work around.

What phone are you using?

All the pictures I found of the F90BT has a input jack on the face of the unit. Are you saying yours does not?

I just tried again and got a full refund and full service till they close their doors in 2012! Thanks for all that were persistent about me calling back. I'm not sure why the first two people I talked to were so unwilling to do anything for me, but the third call finally worked.

No confusion here. I was told that I had to cancel my service to get a full refund on my lifetime card or wait until 2012 and get a pro-rated refund on balance owed (which they could not tell me what that would be). I was not offered a continued service with a canceled subscription.

I got the same thing when I called, no refund on the lifetime unless They totally shut down my service, but once the subscription ran out in 2012, they will send me a pro-rated check for the difference.

Mine seems to work fine, before and after the update.

You are wrong....If you are driving West in 3D, then the compass arrow (red part) should be pointing to the Right!

What camera did you use, I like it.

It's not a problem with the antenna, the GPS works great! The only problem I am having (knock on wood) with the 3.0 upgrade is the default city is locked on Buffalo. I can change it to another city and it will find and route me to the selected locations, but the next time I go to input another location, it comes up with Buffalo as the default.

I have run the Nav many times since upgrading and it hasn't changed yet. Still hoping someone has an answer.

Try this...

After upgrading to 3.0, my default city for looking up addresses became Buffalo, NY. That's an hours drive away from my home town. My home address is entered as a Rochester, NY address. Does anyone know how to change to default city? It's a real pain to have too change it to Rochester every time I have to look up a local location, which is the majority of the time. My car has never been to Buffalo, so I have no idea how that became the default.

Does anyone know if there is a crossover already installed in the XB's and where it might be?

I found it a little easier to use the airvents on either side of the radio to pull from. It pulls off really easy. There is also a small fascia piece mounted just under the radio that must come off too. This piece also just pulls off easy.

What is the purpose of the relay?

That's it! Just be careful, my RS6 didn't have a light green parking brake wire like all the mod's say to ground, mine was a different color.

No problem, it's nice to know there is a place to come for the answers. I just updated my F900BT with the new software update, I'll keep you posted!

Let us know how it goes. The Mod is nice since it will allow you to put in an address for the Nav without having to pull over and engage the emergency brake! We used it last night and it was great not having to pull over and stop.

I'll be saving mine in case of a system problem requiring a reinstall.

Are you getting the additional three MSN Direct items?

My steering wheel controls work fine with the F900BT on my RS6. The "Hand Brake Mod" will allow you do do "everything" while driving, even watch a DVD, though it's not recommended. LOL

I do have a RS6 with the F900BT. I did the Hardware Mod and it works great. The mod is a little different on our cars because the wiring harness used, uses some different wire colors. There is no Light Green Hand Brake wire going to the back of our unit, like the mod calls for, at least there wasn't on mine. The Hand Brake wire on our car, if I remember correctly is a Red & White wire. It will be the third wire over from the Black wire on the Black connector. The link below will show you the pinouts and it's the position 9 wire on the Power Supply connector is the one you want. h