901SoundsofMemphis
Members-
Content Count
16 -
Joined
-
Last visited
About 901SoundsofMemphis
-
Rank
- Birthday 08/31/1983
Contact Methods
-
AIM
myspace.com/901sounds
-
Website URL
http://www.901sounds.net
Profile Information
-
Gender
Male
-
Location
Memphis Tennessee
-
Interests
Auto Accessories
-
bluetooth firmware missing
901SoundsofMemphis replied to swong46's topic in Problems/Troubleshooting
hey , our installer and i just finished installing avic-120bt in a honda crv. units looks great. when it comes to the bluetooth mode, its operational . phonebook , call history is syncing up. but for some reason, incoming calls to the head unit doing ring threw the speakers. and when i pick up the call the other person on the other end of the phone hear me clearly, but i cant hear them at all. and when i dial a number from the head unit i cant hear anything from my speakers. I made sure my volume controls we set to max , i pretty sure that has nothing to do with it. im not using no amps, ever -
Has anyone gotton their hands on a AVIC-Z2 yet?
901SoundsofMemphis replied to SUPER DUTY 2008's topic in Hacks/Mods
u think if ground all empty pins at same time unit will work? -
we drove on the express way playing with the resistors. parking brake wire gives u 4.88 volts before grounging it. and one the empty pins gives u 4.88 volts aswell. we tried diffrent ways but was out of luck.... we'll keep tring difrent resistors
-
Bypass AVIC-Z2 (old topic from General section)
901SoundsofMemphis replied to 901SoundsofMemphis's topic in Hacks/Mods
normally it wouldn't make a diffrence. we could try it... -
Bypass AVIC-Z2 (old topic from General section)
901SoundsofMemphis replied to 901SoundsofMemphis's topic in Hacks/Mods
we measured them. we got a 4.88 volt in one empty pin. the brake wire was also the same voltages. Disconnecting things that input motion are not the answer. Because the Z1 has internal gyros and can sense motion even with everything external unplugged. I would assume the Z2 is going to do the same thing. The Z1 bypass is http://www.sminntech.com/z1flash.html#newbypass and I'll be willing to bet the Z2 is close. I would focus on the extra holes in connector 2 and measure voltages and work with a resistor for different voltages across the secret hole in connector 2. I would not wor -
Bypass AVIC-Z2 (old topic from General section)
901SoundsofMemphis replied to 901SoundsofMemphis's topic in Hacks/Mods
it cuts off after ur driving over 10 miles or faster.............. -
You're maybe right. we only had them for a week. we still need more time if there is a easier way.
-
If u guys have other way to bypass the unit then post it. This is a temp bypass till we find an easier way.
-
great Idea on the Cam. Looks clean.
-
Really simple. Keep the Parking brake wire grounded all the time. Put a switch on the GPS Ant, How? Tools u need, sawder gun, sawder and splitters. use a switch on GPS Ant. Its a coaxl Ant(Power on the inside and Ground is the outside sheeld) Put switch on the power sheeld wire. its in the center of the wire. It works.When doing so, try not to break the out side sheeld of the wire(make sure the outside layer of the coaxl ant isnt disturbed).Try it When installing unit plug up GPS Ant to unit inorder for it the update location, then unplug Ant and drive. The Only Disadvantage about Bypass must
-
roomer has it we need a resistor to bypass unit. as soon as we figure it out we will post it........
-
speed sense wire for 07 chevy suburban need help
901SoundsofMemphis replied to Doc-audio's topic in Problems/Troubleshooting
if u cant fing it u need to buy a speed pulse genarator ... alpine has one ... we ran in to the same problem... -
Will the ducatiboy bypass for Z1 work with Z2?
901SoundsofMemphis replied to Esfour's topic in Problems/Troubleshooting
they are diffrent. we ordered 5 and still working on bypassing them