osmenog Posted August 8, 2009 Report Share Posted August 8, 2009 My map update shipped at the end of the week, hopefully this will still work with the official update....looking forward to trying. ThanksCarver Be healthy, write, if that... Quote Link to post Share on other sites
touche6784 Posted August 8, 2009 Report Share Posted August 8, 2009 Here is NO WARNING pack Unpack it into APL directory on your F900 with 3.01 software and you never seen any warning messages (expect while the system is startup) http://rapidshare.com/files/265125458/N ... 1.zip.html + mirror http://rapidshare.de/files/48064527/NO_ ... 1.zip.html Be happy ))) your first link has run out of downloads and the file in the second link does not work. Quote Link to post Share on other sites
bryvale Posted August 8, 2009 Report Share Posted August 8, 2009 I put the three file in my APL folder. No Nag screens but it automaticaly puts me to the AV screen and it seems like it takes a really long time to load. Am I missing something? Quote Link to post Share on other sites
Pwnin O'brien1287271010 Posted August 9, 2009 Report Share Posted August 9, 2009 Here is NO WARNING pack Unpack it into APL directory on your F900 with 3.01 software and you never seen any warning messages (expect while the system is startup) http://rapidshare.com/files/265125458/N ... 1.zip.html + mirror http://rapidshare.de/files/48064527/NO_ ... 1.zip.html Be happy ))) Sooooo, is this supposed to remove the warning message that appears when you start up the unit which was on the map screen before it was turned off? Quote Link to post Share on other sites
69sixpackbee Posted August 9, 2009 Report Share Posted August 9, 2009 I put the three file in my APL folder. No Nag screens but it automaticaly puts me to the AV screen and it seems like it takes a really long time to load. Am I missing something? Hopefully you made copies of the originals so you could put them back in and see if it changes the speed. Worth a try, Bud Quote Link to post Share on other sites
mnrivera210 Posted August 9, 2009 Report Share Posted August 9, 2009 Here is a mirror for the 3.01 file: http://www.megaupload.com/?d=N1H4FJ4O Quote Link to post Share on other sites
osmenog Posted August 9, 2009 Report Share Posted August 9, 2009 I put the three file in my APL folder. No Nag screens but it automaticaly puts me to the AV screen and it seems like it takes a really long time to load. Am I missing something? It's true, only if tou have usb flash drive connected to usb port with size more than 16 gigs (with full of music). I have SD card (16 gigs) and usb flash (32 gigs) and i see the difference in time of load... By the way, I have sony wire remote control connected to my device and if I switch between sources using remote control (when the device is in navi screen) it takes more longer time than if I do it from the touch screen. Sometimes it's freeze for a long time... Quote Link to post Share on other sites
Pwnin O'brien1287271010 Posted August 9, 2009 Report Share Posted August 9, 2009 Is this new CommonLib.dll the same as carvers, or does it remove the navi warning message on startup (when the unit was turned off on navi screen)? Also, if I only need the navi message gone, will I just need to copy over the CommonLib.dll or will i need the other files also? Quote Link to post Share on other sites
osmenog Posted August 10, 2009 Report Share Posted August 10, 2009 It's the same file with repares of some bytes. Warning screen not shows. Other files are for deleting warning messages in rear camera source. Quote Link to post Share on other sites
Pwnin O'brien1287271010 Posted August 10, 2009 Report Share Posted August 10, 2009 Ok, so I tested this new CommonLib.dll on my unit... On the first bootup I immediately realized what user bryvale was talking about. If the unit is left on the navigation screen and shut off, on bootup you will not get the nag screen but instead the unit will boot into the AV source screen which was last playing. So technically you do not get a nag screen, but you also do not get the navigation screen. This doesn't save me any button presses because now I must press the Map button to get to the map instead of pressing the Ok button on the navigation warning screen. After restarting the unit, I also noticed that the unit became unstable. The unit becamse very confused going to a black screen, then going to some settings screen. When I finally got to the map screen it was in night mode (it's daytime when I did this all) and wouldn't change to day, then when I pressed on the map screen it too me to the AV source screen which was currently playing. This new CommonLib.dll file is very unstable and does not produce the desired outcome, which is removing the navi warning screen on startup when the unit was left on the navigation screen at shutdown. Quote Link to post Share on other sites
touche6784 Posted August 10, 2009 Report Share Posted August 10, 2009 This new CommonLib.dll file is very unstable and does not produce the desired outcome, which is removing the navi warning screen on startup when the unit was left on the navigation screen at shutdown. Which is why I am waiting for Carver to get his working again. Quote Link to post Share on other sites
mnrivera210 Posted August 11, 2009 Report Share Posted August 11, 2009 I've only had my unit restart on me once, I realized if I push MAP right after it boots up it seems to crash but if I wait a couple of seconds after it loads it has no problems. Quote Link to post Share on other sites
osmenog Posted August 14, 2009 Report Share Posted August 14, 2009 Added the same for F500 NO_WARNINGS_F500BT.zip NO_WARNINGS_3.01.zip Quote Link to post Share on other sites
touche6784 Posted August 14, 2009 Report Share Posted August 14, 2009 Added the same for F500 Did you fix the other one 'cause it is not working. Quote Link to post Share on other sites
carver Posted August 14, 2009 Author Report Share Posted August 14, 2009 upd 14.08.2009 update for 3.010100 version, UC or EW.update from 13.07.2009 with power-up fix also, but at this moment, only for testing[attachment=0]avic_x910_v301_no_warning1-02sec.rar[/attachment] sorry, but at this moment, olly for testing. becouse i only used two times. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.