1coolz71 Posted October 23, 2009 Report Share Posted October 23, 2009 I have scoured this forum for a difinitive answer for this question. After updating to 3.01 following all direction I get the "startup in progress" and rebooting every 5 minutes. I used winrar to unzip the x910 files in Vista I tried 3 different SD cards I tried the included ezrider and multiple others that were posted here I tried this more than a dozen times with the same results I'm not a noob and have done many other successful mods in the past, but this is frustrating me. Many people with the same question here, but no answers Did anyone ever update, have this problem and actually fix it without downgrading and giving up? Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 Did you upgrade the WinCE version? Why did you install the hacked ezRider to upgrade to 3.01? That isn't part of the upgrade. That is part of the hack to use newer maps or certain mods. Did the 3.0 upgrade work fine, and did it stop working after you installed Pioneer's 3.01 upgrade? Be more specific about your steps, you were vague/ Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 I followed this instruction thread viewtopic.php?f=34&t=25751 I used all the files posted there and followed instructions to the T with no problems with the install I used winrar to unzip the downloaded files But the startup message is still there Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 I followed this instruction thread http://avic411.com/forum/viewtopic.php?f=34&t=25751 I used all the files posted there and followed instructions to the T with no problems with the install I used winrar to unzip the downloaded files But the startup message is still there You didn't answer some of my questions. Please re-read my reply and then reply again. Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 Did you upgrade the WinCE version? Why did you install the hacked ezRider to upgrade to 3.01? That isn't part of the upgrade. That is part of the hack to use newer maps or certain mods. Did the 3.0 upgrade work fine, and did it stop working after you installed Pioneer's 3.01 upgrade? Be more specific about your steps, you were vague/ I had the 3.o upgrade hack already done last june and it did work I downloaded the 3.01 910x upgrade from pioneer website I unzipped it with winrar I followed the link above and upgraded my WinCE with the files supplied from pioneer That emptied my "my flashdisk" folder except for the basics booted up with testmode then copy and pasted all the files from the pioneer x910 update after that, the radio didn't work, so I put back my original data folder with the radio stuff Now radio works fine but nav not so good... The x910 update does have a file called ezrider.exe init Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 Did you upgrade the WinCE version? Why did you install the hacked ezRider to upgrade to 3.01? That isn't part of the upgrade. That is part of the hack to use newer maps or certain mods. Did the 3.0 upgrade work fine, and did it stop working after you installed Pioneer's 3.01 upgrade? Be more specific about your steps, you were vague/ I had the 3.o upgrade hack already done last june and it did work I downloaded the 3.01 910x upgrade from pioneer website I unzipped it with winrar I followed the link above and upgraded my WinCE with the files supplied from pioneer That emptied my "my flashdisk" folder except for the basics booted up with testmode then copy and pasted all the files from the pioneer x910 update after that, the radio didn't work, so I put back my original data folder with the radio stuff Now radio works fine but nav not so good... The x910 update does have a file called ezrider.exe init You really messed up. The 3.0 update you said was already done to your unit in June, you were only supposed to copy the LPUE080 folder to a SD card and then boot the unit to perform an automatic update. You were not supposed to delete anything in the flash disk, update WinCE or anything else. Now, re-get the x910bt.zip file and restore the whole flash disk on top of what you have now and see if the unit boots properly. Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 OK I'll put my backup I had of the whole flashdisc directory back in and start over Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 Now I re-installed the original 3.o hack that I was using. I did notice that the system version says Map 1.0006 Ver 2.006 I am running the old ezrider though BTW: "startup " reboot is now gone I tried the LPUE080 file and the system boots up but doesn't see the update - no auto start Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 Now I re-installed the original 3.o hack that I was using.I did notice that the system version says Map 1.0006 Ver 2.006 I am running the old ezrider though BTW: "startup " reboot is now gone I tried the LPUE080 file and the system boots up but doesn't see the update - no auto start the LPUE directory is in the root of the SD card? Go ahead and format the card FAT32 to make sure its done right then re-extract the files from Pioneer's website so the SD card, As long as the unit is acting right, I wouldn't worry so much about what version it says you're running. Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 I was trying you use the new maps and 3.0 interfaces that are out now I formatted a new SD card with FAT32 and loaded LPUE080 It's the only file on the card No luck Quote Link to post Share on other sites
bloodninja Posted October 23, 2009 Report Share Posted October 23, 2009 Did you upgrade the WinCE version? Why did you install the hacked ezRider to upgrade to 3.01? That isn't part of the upgrade. That is part of the hack to use newer maps or certain mods. Did the 3.0 upgrade work fine, and did it stop working after you installed Pioneer's 3.01 upgrade? Be more specific about your steps, you were vague/ I had the 3.o upgrade hack already done last june and it did work I downloaded the 3.01 910x upgrade from pioneer website I unzipped it with winrar I followed the link above and upgraded my WinCE with the files supplied from pioneer That emptied my "my flashdisk" folder except for the basics booted up with testmode then copy and pasted all the files from the pioneer x910 update after that, the radio didn't work, so I put back my original data folder with the radio stuff Now radio works fine but nav not so good... The x910 update does have a file called ezrider.exe init Are you sure the X-update is what you wanted? Pioneer says that the x-version firmware will sort of work, but not really... it obviously isn't official or it would be on the updates page on the f-series webpage. Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 I was trying you use the new maps and 3.0 interfaces that are out now I formatted a new SD card with FAT32 and loaded LPUE080 It's the only file on the card No luck file or directory? LPEU080's directory should have 510 files from it. Does yours? Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 Did you upgrade the WinCE version? Why did you install the hacked ezRider to upgrade to 3.01? That isn't part of the upgrade. That is part of the hack to use newer maps or certain mods. Did the 3.0 upgrade work fine, and did it stop working after you installed Pioneer's 3.01 upgrade? Be more specific about your steps, you were vague/ I had the 3.o upgrade hack already done last june and it did work I downloaded the 3.01 910x upgrade from pioneer website I unzipped it with winrar I followed the link above and upgraded my WinCE with the files supplied from pioneer That emptied my "my flashdisk" folder except for the basics booted up with testmode then copy and pasted all the files from the pioneer x910 update after that, the radio didn't work, so I put back my original data folder with the radio stuff Now radio works fine but nav not so good... The x910 update does have a file called ezrider.exe init Are you sure the X-update is what you wanted? Pioneer says that the x-version firmware will sort of work, but not really... it obviously isn't official or it would be on the updates page on the f-series webpage. I don't think you've really kept up with whats been going on in the F series 3.0 hacks lately. Quote Link to post Share on other sites
1coolz71 Posted October 23, 2009 Author Report Share Posted October 23, 2009 YUP, The directory has exactly 510 files I think I'll just pay the $120 to get to 3.0 and newer maps I must be stupid or something, I thought other people were putting the X910 updates on the F series on this thread viewtopic.php?f=34&t=25751 Quote Link to post Share on other sites
terron Posted October 23, 2009 Report Share Posted October 23, 2009 YUP, The directory has exactly 510 files I think I'll just pay the $120 to get to 3.0 and newer maps I must be stupid or something, I thought other people were putting the X910 updates on the F series on this thread http://avic411.com/forum/viewtopic.php?f=34&t=25751 You're not stupid I put the x910bt.zip contents on my F700BT to get to 3.0 then used Pioneer's X910BT update to get to 3.01 and didn't have any of the troubles you're having. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.