crtlv

wow such cynics ohh well ill put up the pics of it working soon

not a problem ill post up pics of the install this week along with pics and perhaps video of the cd Ib100 working on a f series as well just to dispell the notion.because the cd I100II does show up as EXT 1 on the f series and so does the cd changer

i usually dont chime in on these kind of off topic subjects but this has gotten my attention. First off its a open forum,If someone doesnt like a f series or anything for that matter they are entitled to there opinion. Now if they are just spewing venom and not offering any kind of factual reasons as to why the dont like the product then thats just a waste. The F sereies In my Opinion isnt a bad unit,People are resistant to change and sometimes unwilling to have a open mind. Does the f series take time to load?Sure and honestly i dont like the loading time,But have you seen the OEM Nav sys

what mistake?Its in his car and working Why call someone to tell them something wont work when its already Installed and working with a F series? Pioneer says a cdIb100II wont work with the F series either and i have installed that combination 2 times already. As i previously stated I didnt like the way the Ib100 worked with the F series but i needed to use it because my customer Needed Ipod And 2 Av inputs In his install,So yes does it work YES,Did it work as I would like it?NO,Do you hit ipod and it come on ?NO do you hit EXT 1 and it work YES.Does pioneer even Acknowlege it work?NO. Bu

sorry didnt notice that i did not put up the link to the fix that i posted here for another similar issue heres the link http://www.avic411.com/forum/viewtopic.php?t=20327 and here is the fix i recomend If you have a car or truck that needs all the Accesories powered up "Ie some chevys and fords" during remote start or wait to start situations you should do this to isolate your radio from turning on during remote start or wait to start. Have your installer isolate the 12v turn on wire to your stereo using a standard 5 pole "Bosch"relay. Have them use the ground when running outp

ok when i get my customer with his f900 and a 12 disc pioneer back in ill take pictures and post up here

actually you can connect a pioneer cd changer or the older dvd changer from pioneer as well It works thru the IP bus Ie the blue plug in back of the F series wrong the F series will not accept any DVD or CD changer from pioneers website How do I connect the XDV-P6 to the AVIC-D3? Follow the steps below when connecting an XDV-P6 to an AVIC-D3: Connection; 1. Connect the IP-BUS and Composite video cable to the output of the XDV-P6 to the input of the AVIC-D3. 2. Set the dip switch of the XDV-P6 to IP-Bus mode. Setup; 1. Press the Menu button. 2. Press th

You cannot connect the stock Xm tuner to the avic,If you use the gmahl1 from peripheral it will retain the stock XM for the rear seat controls only on the newer IE 2007-present GMs. To tell if you have bose or non bose if you have tweeters on your A pillar usually its bose also Higher end gms With leather interiors and power options have the bose setup,and its displayed on the deck on older gms as well

actually you can connect a pioneer cd changer or the older dvd changer from pioneer as well It works thru the IP bus Ie the blue plug in back of the F series

you cant reconect your stock 6 disc to the pioneer unit.and as far as i know there isnt any company or way to interface the two units, sorry to say your changer is dead

most of the chevy interfaces that allow install and retain onstar will disconnect the Acc wire when onstar is active and then turn on the acc wire when onstar is off. So yes its normal that your radio will shut off

where did you connect the white wire?also what mode is the unit set to?have you fully cleared out the units preset memory? Again as previously stated,95%of the problems are user and installer error,very rare that one of these is bad out the box.

ok if removing 4 bolts running new wires taping into a fuse panel is easier than a 30 second relay install is easier then by all means go that route. And with the relay you still keep everything as it shoud be and retain the acc function and RAP.But what do i know what works for you works.Ide just keep it simple

sounds as if you may have to custom install the deck into the dash opening but your Sw control will work just fine.You can go to pac's website and see the install instructions. The old version should be fine i cant see the new version being any help on that car being that its worked just fine in the past and all the new revisions are for the newer canbus equiped vehicles

all depends on how the remote starter is set up.Some cars and trucks require that the Accesory wires from the ignition switch be powered up during remote start.Some cars use the accesory circut to power the eletric fans or even the A/C compressor and thoes are things needed when you want your vehicle cooled while under remote start control. Again its a vehicle specific or even installer specific issue.My posted soloution will fix your problem