subaru_terrence

i had 1.1.2 on my ipod before too and it couldnt work with my x940 at all. However, as long as i updated my ipod to the latest firmware, it is working like a champ!

I have a 2011 subaru sti that has installed X940bt along with Axxess ASWC recently. Let just say the auto detection for all of the steering control buttons sucks. Anyway, I had to manually program all of the buttons. However, I dont seem to find the option of voice command or pop up the phone menu from the Axxess' installation manual. Can anyone give me some help? I do remember before I programmed all of the buttons, there was one button could bring up the phone menu but since the rest of the buttons are not doing the proper function, i had no choice but to manually program them.

i would like to know too!

I downloaded the ipod_24.1.0.2 firmware and tried this solution download the firmware place it on your desktop go to itunes hold shift and click restore pick your new firmware on your desktop and let it do its thing I hold shift and click restore...it said they cant find any firmware then i tried this solution instead http://spr33.co.uk/wp/archives/downgrad ... re-102-101 i cant even find the folder in my vista in step 3

only 1.0.2 for the classic? what if I have 1.1.2? Is there any solution with it? by the way, it is kinda off topic but when i play videos with my ipod normally, it cant play videos non-stop.... i pretty much have to choose the next video whenever the previous one stops...it is pretty annoying if I am just playing music videos

if I hook up the vss wire.. I can still play movies while driving right?

I just installed a rear view camera on my car today. I hooked it up to the reverse wire so it will turn on when I am in R only. I thought the D3 will automatically turn on the rear view screen once I am in Reverse but for mine....nothing happened....I had to hit Map button then Rear view button everytime I want to take a look at my rear screen My question is, how do I change the setting in order to make the D3 changes to the rear view screen once I am in reverse?

I have some high pitch alternator noise, so I went to ground the d3 to the chassis today. The alternator noise isnt as loud as before but still there. However, when I look at my speed sensor, it said the function is not available. Also, the gps is about 1 block off my actual position. everytime when I start my car, it will tell me something about storefront mode and how the gps will work according to my current position or something. Does anyone know what is wrong? I checked the GPS antenna status at "Connection Status", it seems perfectly fine.

i reset the 3d calibration already....but same thing happened to the speed... i was clearly slowing down the car but the speed that was shown on the screen was still increasing

thanks a lot!! I will definitely do that... Now you remind me something, the installer didnt hook up with VSS since the speed pulse shows me "0" since my deck is bypassed. For the gps signal, it shows me "NOK" I THINK when the gps is acting weird

I don't have my VSS wire connected right now. The D3 has my speed PERFECTLY matched to my speedometer. I don't think it's using the gyros to calculate speed. It can calculate your speed from the GPS signals - like any hand-held GPS can do. is that mean there is something wrong with my gps antenna? I just dont get how it was working perfectly fine before I disconnect the battery

Hey, can anyone please tell me the colour of vss and reverse for 02 subaru legacy please? thanks in advance!

I will check my connection tomorrow morning for sure. By the way, what colour is the VSS wire?

I dont know if my theory is right or not but let say the VSS wire has come disconnected, isnt the speed on my screen wont move at all? I just dont get how come the speed and my gps arent accurate anymore after I disconnect my battery. :S should I disconnect again?

I have alternator whine in my 02 subaru legacy as well. The installation was done by some audio shop so I dont know too much about grounding and stuff. However, I am pretty sure the guy didnt ground anything to the chassis. If I want to ground it to the chassis, what do I have to do?